unpackIng
When unpacking, make sure that the item is
intact and undamaged. If any parts are missing or
broken, please call Harbor Freight Tools at
1-800-444-3353 as soon as possible.
250 lb. Truck
ladder rack
66187
ImporTanT saFeTY
InFormaTIon
Installation precautions
1.
2.
3.
4.
Follow DOT regulations regarding installation
and use.
Verify that installation surface has no hidden
utility lines before drilling or driving screws.
InsTrucTIons and
precauTIons
Install only according to these instructions.
Improper installation can create hazards.
Wear ANSI-approved safety goggles and
heavy-duty work gloves during installation.
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
5.
6.
Keep installation area clean and well lit.
Keep bystanders out of the area during
installation.
saVe THese
InsTrucTIons.
read all
7.
Do not install when tired or when under the
influence of drugs or medication.
use precautions
precauTIons and
InsTrucTIons.
Copyright 2008 by Harbor Freight Tools . All
rights reserved. No portion of this document or any
artwork contained herein may be reproduced in any
shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this document
may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the
product described herein. Tools required for installation
and service may not be included.
1.
Do not exceed 250 lb. weight capacity,
distributed evenly across both Frames. Be
aware of dynamic loading! Sudden load
movement may briefly create excess load
causing product failure.
©
®
2.
3.
Strap ladder securely to rack.
When expanding the Arm (6), leave at least
2.5” of the tube in the Frame (1).
4.
5.
Use as intended only.
Inspect before every use; do not use if parts
loose or damaged.
For technical questions or replacement parts,
please call 1-800-444-3353.
6.
Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
specIFIcaTIons
Weight Capacity
Arm Width
250 lb.
19”-34”
53”
Rack Height
manual revised 09b
rear rack Installation
6.
7.
Insert Arm (6) into Frame (1) and secure with
Jam Bolt (D), as shown above.
1.
2.
Slide Rear Mounting Bracket (3) over Rear
Base (5) as shown above. Temporarily se-
cure in place with Jam Bolt (D).
Attach Ladder Stop (7) to Frame (1) using
Carriage Bolt (M), Washer (N), and Nylon
Insert Nut (P).
Place the Base/Bracket assembly as shown
below at the passenger side of the vehicle
near the tailgate. Loosen the Jam Bolt and
allow the Base to slide down so the foot rests
flat on the truck bed.
8.
9.
Install Strap (8) through the bracket on the
Frame (1).
Slide the assembled Frame (1) into the Front
Base (4).
3.
4.
Mark the bedrail at center of the holes, 4
holes in the side and 1 hole on the truck bed.
Any one of the holes in the Base can be
used for the truck bed hole. Set the assem-
bly aside.
Drill for and install 5 Blind Fasteners (H) in
the locations marked in the previous step.
(bed)
5.
Attach the assembly to the Blind Fasteners
as shown above using Bolts (E), Washers
(F), and Spring Washers (G) - as shown
above.
SKU 66187
For technical questions, please call 1-800-444-3353.
Page 3
operaTIon
1.
Measure the width of the ladder to be mount-
ed on top of the Ladder Rack and slide the
Arms (6) to fit the ladder allowing no more
than 2” of space between ladder and Ladder
Rack. Tighten the Jam Bolts (4) securely.
2.
3.
Lay the ladder on top of the Frames (1)
between the vertical arms and slide it forward
until it contacts the Ladder Stop (7).
Use the Straps (8) to wrap around ladder
rungs and securely hold the ladder in place
using hook and loop system attached to
Straps.
6.
7.
8.
Insert Arm (6) into Frame (1) and secure with
Jam Bolt (D), as shown above.
Install Strap (8) through the bracket on the
Frame (1).
Slide the assembled Frame (1) into the Rear
Base (5).
after Installation
1.
2.
If desired, a Cleat (9) can be installed on
each Frame (1). Place the Cleat in the de-
sired location and mark the holes. Drill 1/4”
holes in the locations shown and install the
Cleats, using Screws (J), Washers (K), and
Nylon Insert Nuts (L).
Inspect and test vehicle systems thoroughly,
especially lighting and braking systems, to
confirm that they were not damaged during
installation.
SKU 66187
For technical questions, please call 1-800-444-3353.
Page 4
parTs lIsT and dIagram
part
A
B
C
D
E
F
G
H
J
K
L
M
N
P
description
Installation Bolt M8 x 55 (tool)
Flat Washer Ø8 (tool)
Installation Nut (tool)
Jam Bolt
Hex Bolt M8 x 30
Flat Washer Ø8
Spring Washer Ø8
Blind Fastener
Screw M5 x 70
Qty.
part
description
Qty.
1
1
1
4
9
9
9
9
4
4
4
1
1
1
1
2
3
4
5
6
7
8
9
Frame
2
1
1
1
1
2
1
2
2
Front Mounting Bracket
Rear Mounting Bracket
Front Base
Rear Base
Arm
Ladder Stop
Strap
Cleat
Flat Washer Ø5
note:Some parts are listed and shown for illustra-
tion purposes only, and are not available
individually as replacement parts.
Nylon Insert Nut M5
Carriage Bolt M10 x 80
Flat Washer Ø10
Nylon Insert Nut M10
m
d
e
a
J
F
g
k
b
c
n
l
p
H
1
4
2
5
9
8
3
6
7
record serial number Here:
note:If product has no serial number, record month and year of purchase instead.
SKU 66187
For technical questions, please call 1-800-444-3353.
Page 5
please read THe FolloWIng
lImITed 90 daY WarranTY
careFullY
Harbor Freight Tools Co. makes every effort
to assure that its products meet high quality and
durability standards, and warrants to the original
purchaser that this product is free from defects in
materials and workmanship for the period of 90
days from the date of purchase. This warranty does
not apply to damage due directly or indirectly, to
misuse, abuse, negligence or accidents, repairs
or alterations outside our facilities, criminal activ-
ity, improper installation, normal wear and tear, or
to lack of maintenance. We shall in no event be
liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential
damages arising from the use of our product. Some
states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL
OTHER WARRANTIES, ExPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANT-
ABILITy AND FITNESS.
The mAnuFAcTurer AnD/or DIsTrIBuTor
HAS PROVIDED THE PARTS LIST AND
ASSEMBLy DIAGRAM IN THIS DOCUMENT AS
A REFERENCE TOOL ONLy. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES
ANy REPRESENTATION OR WARRANTy OF
ANy KIND TO THE BUyER THAT HE OR SHE
IS qUALIFIED TO MAKE ANy REPAIRS TO THE
PRODUCT, OR THAT HE OR SHE IS qUALIFIED
TO REPLACE ANy PARTS OF THE PRODUCT.
In FAcT, The mAnuFAcTurer AnD/or
DISTRIBUTOR ExPRESSLy STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN By CERTIFIED
AND LICENSED TECHNICIANS, AND NOT By
THE BUyER. THE BUyER ASSUMES ALL RISK
AND LIABILITy ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
To take advantage of this warranty, the prod-
uct or part must be returned to us with transporta-
tion charges prepaid. Proof of purchase date and
an explanation of the complaint must accompany
the merchandise. If our inspection verifies the de-
fect, we will either repair or replace the product at
our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you
with a replacement. We will return repaired prod-
ucts at our expense, but if we determine there is
no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights
and you may also have other rights which vary
from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 •
Camarillo, CA 93011 • (800) 444-3353
SKU 66187
For technical questions, please call 1-800-444-3353.
Page 6
|